Search results
Jump to navigation
Jump to search
- ...ed or two [[sprocket]]s connected with a common [[roller chain]], or the [[circumference]]s of two [[pulley]]s connected with a drive [[belt (mechanical)|belt]]. Since the number of teeth is also [[proportional]] to the [[circumference]] of the gear wheel (the bigger the wheel the more teeth it has) the gear r6 KB (1,061 words) - 07:42, 9 August 2009
- When a vehicle is steered, it follows a path which is part of the circumference of its '''turning circle''', which will have a centre point somewhere along2 KB (321 words) - 10:10, 2 August 2009
- ...is sealed in each cylinder by a series of metal rings that fit around the circumference of the piston in machined grooves. These rings are made of some variety of3 KB (441 words) - 19:45, 31 March 2009
- ...is sealed in each cylinder by a series of metal rings that fit around the circumference of the piston in machined grooves. These rings are made of some variety of3 KB (492 words) - 00:06, 8 August 2009
- ...rks, either directly or via selector rods. These tracks deviate around the circumference and as the drum rotates, the selector forks running in the tracks are moved7 KB (1,143 words) - 23:27, 3 July 2009
- ...hickness of used/worn ring (face wear in bore) essentially decreasing face circumference of ring and thereby increasing size of ring end gap.)6 KB (1,010 words) - 09:55, 25 September 2009
- ...lamped between them. Anywhere between 16 and 32 bolts are used around the circumference of the wheel to keep the clamp tight. The rings and bolts can cause proble3 KB (523 words) - 10:42, 8 October 2009
- ...re related by the [[angular speed]] where each revolution results in the [[circumference]] of the circle being travelled by the force that is generating the torque. For a rotating object, the ''linear distance'' covered at the [[circumference]] in a [[radian]] of rotation is the product of the radius with the angular13 KB (2,031 words) - 10:19, 27 September 2009
- ...nufacturing success. During drawing (pulling of the glass to reduce fiber circumference) the viscosity should be relatively low. If it is too high the fiber will11 KB (1,828 words) - 13:41, 11 February 2009
- ...driven on Italy's Nardo Prototipo proving ground, a circular track with a circumference of 12.5km. This exceeded the McLaren's record [http://www.koenigsegg.com/re9 KB (1,324 words) - 13:26, 8 October 2009
- * Metres of development = '''Circumference''' of drive wheel in metres × number of teeth in front chainring / nu24 KB (3,509 words) - 23:29, 3 July 2009
- ...fice, in a quantity sufficient to disperse across the piston crown and the circumference of the top ring land, and thereby effect the mentioned seal. If a second co16 KB (2,479 words) - 14:53, 25 September 2009
- ...cker-arm engines, raised to a capacity of 833cc by increasing the cylinder circumference and clearance. They were first unveiled at the Geneva Motor Show in 1959, a18 KB (2,744 words) - 21:44, 19 November 2011
- ..." on its inner surface bridge two circular rings with teeth on their outer circumference; one attached to the gear, one to the shaft. (One collar typically serves f40 KB (6,454 words) - 10:28, 15 July 2009
- ...e''' or '''tire''' (see [[spelling differences]]) is a device covering the circumference of a [[wheel]]. It is an essential part of most ground [[vehicles]] and is30 KB (4,915 words) - 10:59, 5 March 2017
- ...construction is the Large Hadron Collider (LHC) which, at 27 kilometers in circumference, already holds the title of "world's largest machine," when finished, will50 KB (8,151 words) - 14:44, 9 August 2009
- ...ance offered by the motorcycle (and rider) to the passing air. Around the circumference of the dial, red lights at each degree provide a visual indicator to the ri53 KB (7,792 words) - 12:53, 9 December 2009