Search results

• Four-stroke cycle
  ...lower runs in (as opposed to following the outside profile only), others a crank arrangement similar to the crankshaft. The drawback of the system is its in
  11 KB (1,775 words) - 09:48, 2 August 2009
• Capriolo
  ...sefull the centrifugal oil filter, pity that it is mounted in front to the crank shaft so to oblige to remove the head, cilinder, flywheel and frontal case ...from Capriolo 75, the gearbox have the same longitudinal orientation like crank shaft, but the final trasmission drive use a chain inside a shaft so to avo
  23 KB (3,832 words) - 09:44, 14 April 2011
• Reciprocating engine
  '''5''' - Crank<br>
  9 KB (1,400 words) - 18:37, 9 August 2011
• Four stroke cycle
  ...lower runs in (as opposed to following the outside profile only), others a crank arrangement similar to the crankshaft. The drawback of the system is its in
  12 KB (1,944 words) - 22:56, 14 June 2009
• Sleeve valve
  ...that the sleeve can be turned. Otherwise a single sleeve is operated by a crank driven from the crankshaft, the sleeve moves in a circular path opening the
  9 KB (1,597 words) - 08:25, 8 October 2009
• Itala
  The magnet power is low voltage. The starter is crank, lights, kerosene lanterns for the location and number plate and acetylene
  8 KB (1,143 words) - 09:55, 18 November 2011
• Two stroke
  :Crank is at 0 or 360°.
  15 KB (2,394 words) - 23:48, 11 September 2009
• Ducati Singles
  ...e 16&nbsp;hp at 11,500&nbsp;rpm, its true rev limit, while the Desmo could crank out 19&nbsp;hp at 12,500&nbsp;rpm and could “safely” (bottom end permit
  13 KB (2,018 words) - 22:22, 22 September 2009
• Supercharger
  It is also possible to drive the blower from the crank shaft and use an exhaust turbine for output power.
  15 KB (2,335 words) - 22:54, 14 June 2009
• Graphite-reinforced plastic
  ...erations into tube profiles. CFRP frames, forks, handlebars, seatposts and crank arms are becoming commonplace on medium- and higher-priced bicycles. CFRP f
  12 KB (1,819 words) - 19:04, 14 November 2010
• Suspension (vehicle)
  ...[[Horstmann suspension]] was a variation which used a combination of bell crank and exterior coil springs, in use from the 1930s to the 1990s.
  29 KB (4,645 words) - 10:46, 8 October 2009
• Dirt speedway racing
  ...engines, and most start with an aluminum 350 in³ Chevy block with stroker crank, high flow degreed aluminum cylinder heads and high-flow exhaust headers. E
  13 KB (2,197 words) - 09:41, 8 October 2009
• History of the bicycle
  ...Call]], of Kilmarnock in 1869. The design could not compete with the front-crank velocipede of the Lallement/Michaux type, however, despite McCall's all ste
  34 KB (5,162 words) - 18:37, 23 April 2009
• Motorcycle
  ...charcoal-fired two-cylinder engine, whose connecting rods directly drive a crank on the rear wheel. This machine predates the invention of the safety bicycl ...the four stroke; it consists of only two moving parts--the piston and the crank. A four stroke engine has between six and ten moving parts, depending on th
  38 KB (6,073 words) - 20:26, 6 July 2009
• Bicycle
  ...system employed a pair of treadle drives connected by rods to a rear wheel crank, rather like a steam locomotive's driveshaft. Although the design was copie ...e the [[crankset]], which fit into the [[bottom bracket]]. Attached to the crank is the ''chainring'' or sprocket which drives the [[bicycle chain|chain]],
  53 KB (8,173 words) - 09:32, 25 September 2009
• Fuel injection
  :*Crank/Cam Position: [[Hall effect sensor]]
  35 KB (5,222 words) - 08:19, 11 June 2009
• Diesel engine
  ...most of today's modern engines. The timing is usually measured in units of crank angle of the piston before [[Top Dead Center]] (TDC). For example, if the [
  33 KB (5,114 words) - 23:11, 23 September 2009
• Aluminium
  [[Image:ferrengalum.jpg|thumb|right|250px|<BIG><center>Ferrari Crank Case made of aluminium</center></BIG>]]
  35 KB (5,288 words) - 22:04, 13 July 2007
• Lancia Ardea
  ...t to the propeller (between which the maggiorazione of the diameter of the crank hinges and the adoption of connecting rods in printed special steel instead
  56 KB (8,812 words) - 11:18, 17 September 2010
• Moto Guzzi
  ...ing high between the cylinders, with an alternator sited on the end of the crank at the front of the engine. The 750S and 750 S3 followed, but it was the 85
  53 KB (7,792 words) - 12:53, 9 December 2009

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)